SMART MASTER SUITE 1.0.2
Created by Andrea Di Tella
https://www.andreaditella.com

Free to use with no limitations. To support development, you can make an
optional donation of any amount:
https://www.paypal.com/paypalme/andreaditella

INSTALLATION - WINDOWS 64-BIT

1. Close your audio applications and extract the ZIP archive.
2. Copy the entire SmartMasterSuite.vst3 FOLDER into:
   C:\Program Files\Common Files\VST3
   Administrator permission may be required.
3. Open your DAW and rescan its VST3 plugins if necessary.
4. Insert "Smart Master Suite" on the master bus, normally as the final
   sound-processing effect before your final meters.

The plugin includes its C++ runtime. A separate Visual C++ runtime installer
is not required. The VST3 folder must remain intact; do not copy only its
internal file. Windows 10 or newer, 64-bit, and a compatible VST3 host are required.

QUICK START

1. Finish your mix and remove any accidental clipping before this plugin.
2. Choose a CHARACTER: WARM, BALANCED or OPEN.
3. Set LOUDNESS to a target such as -14 LUFS and CEILING to -1 dBTP.
   These are starting values, not a delivery requirement for every service.
4. Play a representative section of your song and press ANALYZE.
5. Keep playback running for about 20 seconds. The plugin analyses locally
   and proposes conservative tone and compression settings. It then measures
   the proposed processing to calibrate the loudness gain.
6. When MASTER READY appears, listen and adjust the controls to taste.
7. Use GAIN MATCH and BYPASS to compare with your original mix.
8. Turn GAIN MATCH and BYPASS OFF before exporting your mastered audio.

Analysis is a useful starting point, not a guarantee of a perfect master.
Choose a section that represents the energy and instrumentation of the song.
Silence or insufficient audible material is rejected and existing settings
are kept. Press CANCEL to abandon analysis without replacing your settings.
If playback is stopped, collection pauses until the host sends more audio;
some hosts continue sending silent audio while stopped. Keep playback active.
The final calculation takes a short additional time. Audio continues playing.

MAIN CONTROLS

INPUT: -18 to +18 dB input trim. Correct the mix level before analysis.
AMOUNT: 0 to 100%. Blends the tone, compression, de-essing and stereo width
  processing. Loudness gain and the final limiter remain active at 0%.
DYNAMICS: 0 to 100%. Linked, gentle-knee glue compression; larger values
  apply a lower threshold and stronger ratio. 0% disables compression.
WIDTH: 0 to 150%. 100% preserves the stereo width; 0% sums to mono;
  values above 100% widen the sides. On a mono track this control has no effect.
LOUDNESS: -20 to -6 LUFS target. ANALYZE calibrates the gain for your material.
  Before analysis it uses a nominal input reference, so use the meters and ears.
CEILING: -6 to 0 dBTP output limit. The oversampled, linked lookahead limiter
  includes reconstruction headroom. Prioritize a safe ceiling over excessive
  loudness; a dense or transient mix may not reach a high requested LUFS value.

CHARACTER

WARM adds a subtle low-end lift and softer highs.
BALANCED is neutral.
OPEN adds a subtle high-frequency lift and slightly leaner lows.
These are original tonal profiles, not models of another product.

ADVANCED CONTROLS

BASS: +/-6 dB low shelf at 110 Hz.
MIDS: +/-6 dB broad bell at 650 Hz.
TREBLE: +/-6 dB high shelf at 8.5 kHz.
PRESENCE: +/-6 dB broad bell at 3.2 kHz.
DE-ESSER: 0 to 100% linked dynamic reduction of bright high-frequency content.
HIGH PASS: 20 to 80 Hz filter to reduce unwanted subsonic or low-frequency energy.

Reanalyse after substantial mix, character, input trim, EQ, dynamics, width or
Amount changes when you want to recalibrate the loudness target. Analysis
replaces its suggested EQ/dynamics settings, so make creative changes AFTER it.
All parameters and the learned loudness calibration are saved with your project.
The recorded analysis excerpt and running meter history are not saved.

COMPARISON AND METERS

GAIN MATCH gradually approximates the input level for a fairer comparison.
Allow several seconds for it to settle. This is a monitoring aid; disable it
before exporting because it changes the delivered loudness.
BYPASS provides a timing-compensated comparison with the original input.

The spectrum shows INPUT in grey and OUTPUT in amber, with a logarithmic
frequency axis from 20 Hz to 20 kHz. It is a visual guide, not an EQ curve.
INPUT M is the momentary input loudness (LUFS).
OUTPUT I is integrated output loudness (LUFS), accumulated since the last reset.
MAX TRUE PEAK is the held maximum output peak (dBTP).
GAIN RED. shows the larger current compression/limiting reduction (dB).
L/R bars show output sample peaks; red LEDs indicate output sample clipping.
RESET clears the loudness and held peak history on the next audio block.
After analysis, the meters reset automatically for the new master.

USAGE NOTES

Mono-in/mono-out and stereo-in/stereo-out tracks are supported.
Stereo processing links dynamics and limiting to preserve the channel balance.
Lookahead and oversampling introduce a short, fixed latency reported to the DAW.
Keep the host's automatic plugin delay compensation enabled.
Double-click a knob to restore its default. Click its displayed value to type.
The interface can be resized. ABOUT includes the website and donation link.

Check the full song after analysis: a short excerpt may not include the loudest
passage. Always listen to the export and check any destination's requirements.
The limiter ceiling applies to active processing; BYPASS reproduces the original
input, including any clipping already present in that input.

SUPPORT AND DONATIONS
Website: https://www.andreaditella.com
Donate: https://www.paypal.com/paypalme/andreaditella
