SMART RESONANCE EQ 1.0.4
Created by Andrea Di Tella
https://www.andreaditella.com

Free to use with no limitations. Optional donations support development:
https://www.paypal.com/paypalme/andreaditella

INSTALLATION - WINDOWS 64-BIT

Close your DAW. Extract this archive and copy the entire SmartResonanceEQ.vst3
FOLDER into:
    C:\Program Files\Common Files\VST3
Administrator permission may be required. Keep the folder and all its contents
together: do not copy only the internal file. Restart your DAW and rescan its
VST3 plugins if needed. Find "Smart Resonance EQ" in your EQ effects list.
Windows 10 or newer and a compatible 64-bit VST3 host are required.
The C++ runtime is included; no separate Visual C++ runtime installer is needed.

WHAT IT DOES

Four independent parametric bell bands help you find and reduce ringing,
resonant or otherwise unwanted frequency regions. Every band can also boost,
so you can emphasize a frequency while searching and then turn it into a cut.
All bands cover the full frequency range. This is a static EQ: the selected
curves stay in effect until you change them. It is not an automatic dynamic EQ.

AUTOMATIC SEARCH

1. Insert Smart Resonance EQ on an instrument, voice, bus or master track.
2. Play a representative section and press ANALYZE.
3. Keep playback running for about eight seconds. Existing EQ settings continue
   working while the plugin analyses the original input.
4. If persistent, prominent peaks are found, up to four hollow candidate markers
   appear on the graph. No settings are changed automatically.
5. Press APPLY CUTS to replace the four band settings with the suggested cuts.
   The corresponding bands are enabled; any unused bands are disabled.
6. Listen and refine the frequency, gain and Q to suit the recording.

ANALYZE finds candidate resonances, not a definitive list of musical problems.
A sustained note, harmonic or intentional tonal feature may also be suggested.
Use your ears before accepting a cut. No candidates is a valid result; you can
always work manually. Silence and insufficient audible material keep your EQ
unchanged. CANCEL abandons the current search. Collection follows audio sent
by the host, so keep playback active; some hosts send silence while stopped.
Analysis runs locally and does not need an account or internet connection.

FOUR BAND CONTROLS

ON: Enable or disable this band. Its other settings remain available when off.
FREQ: 20 Hz to 20 kHz. Set the centre frequency; every band has the same range.
GAIN: -24 to +12 dB. Negative values cut; positive values boost.
Q / WIDTH: 0.30 to 30.00. Low Q is broad; high Q is narrow and more selective.
LISTEN: Hold the button to hear only the selected frequency region of the
  original input, independent of that band's gain and ON setting. Release to
  return to the full signal. Listen is a temporary monitoring aid, not saved.

A PRACTICAL MANUAL SEARCH

Enable a band, choose a fairly narrow Q, and sweep FREQ while holding Alt and
dragging its graph node to audition the region. You can also increase GAIN
temporarily to make the problem stand out. Once identified, lower GAIN below
zero and adjust Q to remove only as much as needed. Compare with ON/OFF.

Boosting, especially several overlapping bands, can increase output level.
Use OUTPUT to leave enough headroom; red L/R LEDs indicate output clipping.
There is no hidden limiter, compressor, saturation or automatic gain change.

GRAPH AND MOUSE CONTROLS

The horizontal axis is logarithmic frequency, from 20 Hz to 20 kHz.
The vertical scale is EQ gain in dB. The white line shows the combined EQ
response, excluding OUTPUT gain. Each band has its own coloured curve/node.
Grey INPUT and green OUTPUT spectra show audio before/after processing.
Spectra use their own display scale; they are not additional EQ gain curves.

Drag a numbered node horizontally to change FREQ and vertically to change GAIN.
Click near an inactive node, or in empty graph space when a band is available,
to activate and position it. If all bands are active, use their numbered nodes.
Turn the mouse wheel over a node to change Q; Shift-drag also changes Q.
Hold Alt while dragging a node to audition its frequency region. Release the
mouse button to stop auditioning. Double-click a node to reset its gain and Q.
Double-click a knob to restore that parameter's default. Click any displayed
value to type it. Frequency values can be entered as Hz or with k / kHz suffix.

GLOBAL CONTROLS

OUTPUT: -24 to +6 dB final output trim.
BYPASS: Compare with the original, unprocessed signal. Output trim and Listen
  are bypassed too. Switching uses a short transition to avoid clicks.
RESET: Restore the four bands to their disabled defaults and OUTPUT to 0 dB;
  cancels any pending analysis. The BYPASS setting is kept.
ABOUT: Version, author and website. DONATE opens the PayPal donation page.

HOST AND PROJECT BEHAVIOUR

Mono input/mono output and stereo input/stereo output are supported.
Stereo uses the same EQ settings for both channels with independent audio paths.
The plugin adds no latency. All EQ parameters can be automated and are saved
with your DAW project. Analysis history/candidate markers and temporary Listen
state are not saved. Closing the plugin window stops Listen. Hosts that signal
an offline render also disable Listen automatically; release all audition
controls and check BYPASS before exporting.
At low sample rates, filter frequencies are constrained below the Nyquist limit.
The interface is resizable. There are clipping LEDs and no VU meters.

Website: https://www.andreaditella.com
Donate: https://www.paypal.com/paypalme/andreaditella
